OPTIMIZATION OF THE PROCESS OF INDUCTION CENTRIFUGAL WELD OF ANTIFRICTION COATINGS BY THE METHOD OF MATHEMATICAL PLANNING OF THE EXPERIMENT

KURILYONOK Artem A., Junior Researcher, Joint Institute of Mechanical Engineering of the National Academy of Sciences of Belarus, Minsk, Republic of Belarus, This email address is being protected from spambots. You need JavaScript enabled to view it.">This email address is being protected from spambots. You need JavaScript enabled to view it.

BELOTSERKOVSKY Мarat A., D. Sc. in Eng., Assoc. Prof., Head of the Laboratory of Gas-Thermal Methods of Machine Components Hardening, Joint Institute of Mechanical Engineering of the National Academy of Sciences of Belarus, Minsk, Republic of Belarus, This email address is being protected from spambots. You need JavaScript enabled to view it.">This email address is being protected from spambots. You need JavaScript enabled to view it.

The mathematical model has been developed that can be used to select the technological modes of induction centrifugal surfacing, which provide the minimum value of the wear rate of the working surfaces of the deposited coating. The results of computational and experimental modeling are described, from which it can be concluded that in order to obtain the optimum wear rate of the coating material I_q = 6,37÷7,04 · 10^–5 mg / m, the parameters of the induction centrifugal surfacing process should be as follows: temperature isothermal holding T = 1100÷1150 °С, isothermal holding time t = 180÷240 sec, rotation speed ν = 2000÷2250 rpm.

mathematical model, powder batch, antifriction coatings, centrifugal induction weld deposition, nanosized components

• Dorozhkin N.N. Uprochnenie i vosstanovlenie detalei mashin metallicheskimi poroshkami [Hardening and restoration of machine parts with metal powders]. Minsk, Nauka i tehnika, 1975. 152 p.
• Mrochek Zh.A., Kozhuro L.M., Filonov I.P. Progressivnye tehnologii vosstanovlenija i uprochneniya detalej mashin: ucheb. posobie [Progressive technologies of restoration and hardening of machine parts: a manual]. Minsk, Tehnoprint, 2000. 268 p.
• Rjabcev I.A. Indukcionnaja naplavka [Induction weld]. Remont. Vosstanovlenie. Modernizacija [Repairs. Recovery. Modernization], 2005, no. 11, pp. 37–40.
• Gafo Yu.N., Sosnovskij I.A. Thermal parameters for centrifugal induction sintering of powder coatings. Powder Metallurgy and Metal Ceramics, 2009, vol. 48, no. 1–2, pp. 105–111.
• Dorozhkin N.N., Abramovich T.M., Kashicin L.P. Teoreticheskie osnovy poluchenija detalej s pripechenym sloem [Theoretical basis for obtaining parts with a baked layer]. Doklady Akademii nauk BSSR [Reports of the Academy of Sciences of the BSSR], 1974, vol. 18, no. 5, pp. 428–431.
• Danilchenko B.V. Naplavka [Surfacing]. Kiev, Naukova Dumka, 1983, 75 p.
• Penkin N.S., Penkin A.N., Serbin V.M. Osnovy tribologii i tribotehniki [Basics of tribology and tribotechnics]. Moscow, Mashinostroenie, 2008. 206 p.
• Myshkin N.K., Petrokovec M.I. Trenie, smazka, iznos. Fizicheskie osnovy i tehnicheskie prilozhenija tribologii [Friction, lubrication, wear. Physical bases and technical applications of tribology]. Moscow, Fizmatlit, 2007. 386 p.
• Grib V.V., Lazarev G.E. Laboratornye ispytanija materialov na trenie i iznos [Laboratory testing of materials for friction and wear]. Moscow, Nauka, 1968. 141 p.
• Spiridonov A.A. Planirovanie eksperimenta pri issledovanii tehnologicheskih processov [Planning an experiment in the study of technological processes]. Moscow, Mashinostroenie, 1981. 184 p.