MODELING AND EVALUATION OF EFFICIENCY OF THE DUST EJECTION SUCTION BY EXHAUST GASES IN THE AGRICULTURAL HARVESTER DAMPER

KALINOUSKI Alexander A., Mas. Techn. Sc., Design Engineer, OJSC “Gomselmash”, Gomel, Republic of Belarus

CHUPRYNIN Yuriy V., Ph. D. in Eng., Head of the Design and Research Department of Dynamics, Strength, Analytical Reliability, OJSC “Gomselmash”, Gomel, Republic of Belarus, This email address is being protected from spambots. You need JavaScript enabled to view it.">This email address is being protected from spambots. You need JavaScript enabled to view it.

NOVIKOV Alexander A., Deputy Director General for Technical Affairs — Principal Engineer, OJSC “Gomselmash”, Gomel, Republic of Belarus, This email address is being protected from spambots. You need JavaScript enabled to view it.">This email address is being protected from spambots. You need JavaScript enabled to view it.

A methodology and solid-state modeling results of the dust ejection suction process from the engine air inlet with exhaust gases by means of ejector, installed in the self-moving agricultural harvester damper, are given. The results of modeling are compared with the results of experimental researches; conclusions about gained data divergence reasons in some investigated parameters ranges are drawn. Investigated values dependences on changeable parameters are gained. Optimal ejector geometrics providing effective dust suction without engine work conditions deterioration are selected. Recommendations for ejection suction systems engineering are produced at self-moving agricultural harvesters’ development which is successfully used at OJSC “Gomselmash”.

ejector, damper, exhaust gases, differential pressure, mass flow rate, area of passage

• Timoshenko N.S., Semko A.N. Modelirovanie vytyazhnogo vozdukhovoda dlya dugovykh staleplavilnykh pechey [An exhaust air duct modeling for arc steel melting furnaces]. Sbornik nauchnykh statey “Sovremennaya nauka” [Scientific articles collection “Modern science”], 2012, no. 2(10), pp. 10–15.
• Aslamova V.S. Protsess separatsii v vysokoproizvoditelnykh pryamotochnykh tsiklonakh i metody ikh rascheta. Diss. dokt. tekhn. nauk [Separation process in high-duty direct-flow cyclones and methods of their calculation. Extended Abstract of D. Sc. Thesis]. Tomsk, 2009. 40 p.
• Alеkhin S.A., Vasilev V.S., Gerasimenko V.P., Opalev V.A. Issledovanie struynogo ezhektora udaleniya pyli iz vozdukhoochistitelya vykhlopnymi gazami v transportnom dizele [Research of dust removal jet ejector from an air cleaner with exhaust gases in the transport diesel]. Aviatsionnokosmicheskaya tekhnika i tekhnologii [Aerospace engineering and technologies], 2009, no. 8(65), pp. 96–101.
• Klimov V.F., Magueramov L.K., Mihaylov V.V., Shipulin A.A. K voprosu vybora ezhektora sistemy ochistki vozdukha tankov s dvukhtaktnymi dvigatelyami [To the question of choice of air purification tanks with two-cycle engines in ejector system]. Integrirovannye tekhnologii i energosberezhenie [Integrated Technologies and Energy Conservation], 2014, no. 3, pp. 125–129.
• Uspenskiy V.A., Kuznetsov Yu.M. Struynye vakuumnye nasosy [Ejectors]. Мoscow, Mashinostroenie Publ., 1973. 144 p.
• Kalitsun V.I., Drozdov E.V., Komarov A.S., Chizhik K.I. Osnovy gidravliki i aerodinamiki [Fundamental hydraulics and aerodynamics]. Мoscow, Stroyizdat Publ., 2001. 256 p.
• Sokolov E.Ya., Zinger N.M. Struynye apparaty [Jet apparatuses]. Мoscow, Energoizdat Publ., 1989. 352 p.
• Kornev M.S. Sovremennye avtomobilnye vozdukhoochistiteli [Modern automobile air cleaners]. Moscow, Research Institute of Information on the Automotive Industry Publ., 1972. 62 p.
• Deych M.Ye., Zaryankin A.E. Gidrogazodinamika: Ucheb. posobie dlya vuzov [Hydraulic gas dynamics: Tutorial for institutes of higher education]. Мoscow, Energoatomizdat Publ., 1984. 384 p.
• Verkhoturkin Ye.Yu., Pashchenko V.N., Pyasetskiy V.B. Interfeys i generirovanie setki v ANSYS Workbench: ucheb. posobie po kursu “Geometricheskoe modelirovanie v SAPR” [Interface and gridding in ANSYS Workbench: Tutorial, according to the course “Geometrical simulation in CAD”]. Мoscow, MSTU Publishing house n.a. N.E. Bauman, 2013. 63 p.
• Fedorova N.N., Valger S.A., Danilov M.N., Zakharova Yu.V. Osnovy raboty v ANSYS 17 [Basic operation in ANSYS 17]. Мoscow, DMK Press Publ., 2017. 210 p.