Smart Search 


2_2022_sen_6

Title of the article CONSTRUCTION OF DEEP CONTACT FATIGUE CURVES FOR SURFACE-HARDENED GEAR WHEELS
Authors

RUDENKO Sergei P., Ph. D. in Eng., Leading Researcher of the Laboratory of Metallurgy in Mechanical Engineering, Joint Institute of Mechanical Engineering of the NAS of Belarus, Minsk, Republic of Belarus, This email address is being protected from spambots. You need JavaScript enabled to view it.">This email address is being protected from spambots. You need JavaScript enabled to view it.

VALKO Aleksandr L., Senior Researcher of the Laboratory of Metallurgy in Mechanical Engineering, Joint Institute of Mechanical Engineering of the NAS of Belarus, Minsk, Republic of Belarus, This email address is being protected from spambots. You need JavaScript enabled to view it.">This email address is being protected from spambots. You need JavaScript enabled to view it.
In the section MECHANICAL ENGINEERING COMPONENTS
Year 2022
Issue 2(59)
Pages 47–53
Type of article RAR
Index UDK 621.78
DOI https://doi.org/10.46864/1995-0470-2022-2-59-47-53
Abstract Laws of fatigue resistance changes of surface-hardened toothed gears are established. It is shown that the main criterion of serviceability of gear wheels of transmissions of power-saturated machines is deep contact pitting of active surfaces of teeth. Dependence is investigated between the number of cycles before the deep contact destruction of material and the maximal tension of cycle with taking into account the mechanical characteristics and structural parameters in the critical zones of the diffusion layers of the teeth, in which fatigue processes of deep contact destruction of material are developed. Lines of deep contact fatigue of teeth material are constructed by the criterion of equality of hardness value and structural parameters in the zones of fatigue processes development under cyclic contact loading. It is shown, that the deep contact fatigue of gear wheels hardened to a considerable degree is determined by hardness value and structural components of local volumes of teeth subsurface layers. Slope index of the deep contact fatigue lines of gear wheel material have been determined. Correlation coefficients and equations of linear regression have been obtained for each deep contact fatigue line depending on hardness value in the subsurface dangerous zone of the diffusion layer, in which formation and development of fatigue processes occur, leading to the limit state of the highly stressed gear wheels.
Keywords gear wheels, surface hardening, deep contact pitting, deep contact fatigue lines, slope index, linear regression equations
  You can access full text version of the article.
Bibliography
  1. Susin A.A. Khimiko-termicheskoe uprochnenie vysokonapryazhennykh detaley [Chemical heat reinforcement of heavily stressed components]. Minsk, Belorusskaya nauka Publ., 1999. 175 p. (in Russ).
  2. Alekseev V.I., Ananev V.M., Bulygina M.M. Aviatsionnye zubchatye peredachi i reduktory [Aircraft gears and gearboxes]. Moscow, Mashinostroenie Pabl., 1981. 374 p. (in Russ).
  3. Tesker E.I. Sovremennye metody rascheta i povysheniya nesushchey sposobnosti poverkhnostno uprochnennykh zubchatykh peredach transmissiy i privodov [Modern methods of calculating and increasing the load-bearing capacity of surface-hardened gears of transmissions and drives]. Moscow, Mashinostroenie Publ., 2011. 434 p. (in Russ).
  4. Rudenko S.P., Valko A.L. Kontaktnaya ustalost zubchatykh koles transmissiy energonasyshchennykh mashin [Contact fatigue of power transmission gears of energy saturated machines]. Minsk, Belorusskaya nauka Publ., 2014. 126 p. (in Russ).
  5. Rudenko S.P. Issledovanie soprotivleniya kontaktnoy ustalosti poverkhnostno uprochnennykh zubchatykh koles [Investigation of contact fatigue resistance of surface-hardened gear wheels]. Proceedings of the National Academy of Sciences of Belarus. Physical-technical series, 2009, no. 4, pp. 48–53 (in Russ).
  6. Rudenko S.P., Val’ko A.L. Contact fatigue resistance of carburized gears from chromium-nickel steels. Metal science and heat treatment, 2017, vol. 59, iss. 1–2, pp. 60–64. DOI: https:// doi.org/10.1007/s11041-017-0103-3.
  7. Rudenko S.P., Valko A.L., Shyshko S.A., Karpovich P.G. Soprotivlenie kontaktnoy ustalosti krupnomodulnykh zubchatykh koles iz khromonikelevykh staley [Resistance to contact fatigue of coarse-grained gears of chromium-nickel steels]. Mechanics of machines, mechanisms and materials, 2019, no. 1(46), pp. 68–73 (in Russ).
  8. Rudenko S.P., Valko A.L., Mosunov E.I. Tekhnicheskie trebovaniya k kachestvu tsementovannykh sloev zubchatykh koles transmissiy energonasyshchennykh mashin [Technical requirements to quality of carburized layers of gears of power sated cars]. Avtomobilnaya promyshlennost, 2011, no. 9, pp. 33–36 (in Russ).
  9. Rudenko S.P., Sandomirski S.G. Determinirovannaya analiticheskaya model soprotivleniya glubinnoy kontaktnoy ustalosti napryazhennogo materiala [Deterministic analytical model of resistance to deep contact fatigue of a stressed material]. Mechanics of machines, mechanisms and materials, 2021, no. 3, pp. 52–60. DOI: https://doi.org/10.46864/1995-0470-2021-3-56-52-60 (in Russ).
  10. Gold B.V., Obolenskiy E.P., Stefanovich Yu.G., Trofimov O.F. Prochnost i dolgovechnost avtomobilya [Car strength and durability]. Moscow, Mashinostroenie Publ., 1974. 328 p. (in Russ).
  11. State Standard 21354-87. Peredachi zubchatye tsilindricheskie evolventnye vneshnego zatsepleniya. Raschet na prochnost [Cylindrical evolvent gears of external engagement. Strength calculation]. Moscow, Standartov Publ., 1988. 129 p. (in Russ.).
  12. Ryzhov N.M. Tekhnologicheskoe obespechenie soprotivleniya kontaktnoy ustalosti tsementuemykh zubchatykh koles iz teplostoykikh staley [Process maintenance of contact fatigue resistance of carburized gears from heat-resistant steels]. Metallovedenie i termicheskaya obrabotka metallov, 2010, no. 7(661), pp. 39–45 (in Russ).