Smart Search 


1_2023_sen_1

Title of the article DEEP CONTACT ENDURANCE LIMIT OF SURFACE-HARDENED GEARS
Authors

RUDENKO Sergei P., Ph. D. in Eng., Leading Researcher of the Laboratory of Metallurgy in Mechanical Engineering of the R&D Center “Mechanical Engineering Technologies and Processing Equipment”, Joint Institute of Mechanical Engineering of the NAS of Belarus, Minsk, Republic of Belarus, This email address is being protected from spambots. You need JavaScript enabled to view it.">This email address is being protected from spambots. You need JavaScript enabled to view it.

VALKO Aleksandr L., Senior Researcher of the Laboratory of Metallurgy in Mechanical Engineering of the R&D Center “Mechanical Engineering Technologies and Processing Equipment”, Joint Institute of Mechanical Engineering of the NAS of Belarus, Minsk, Republic of Belarus, This email address is being protected from spambots. You need JavaScript enabled to view it.">valсThis email address is being protected from spambots. You need JavaScript enabled to view it.

SANDOMIRSKI Sergei G., D. Sc. in Eng., Assoc. Prof., Head of Laboratory of Metallurgy in Mechanical Engineering of the R&D Center “Mechanical Engineering Technologies and Processing Equipment”, Joint Institute of Mechanical Engineering of the NAS of Belarus, Minsk, Republic of Belarus, This email address is being protected from spambots. You need JavaScript enabled to view it.">This email address is being protected from spambots. You need JavaScript enabled to view it.
In the section DYNAMICS, DURABILITY OF VEHICLES AND STRUCTURES
Year 2023
Issue 1(62)
Pages 5–10
Type of article RAR
Index UDK 621.78
DOI https://doi.org/10.46864/1995-0470-2023-1-62-5-10
Abstract The reliability and durability of gears in most cases depend on the contact endurance of the material of the parts. Analysis of the stress state of surface-hardened gears has shown that under contact loading, the source of primary damage can be located both on the surface and in the depth of the hardened layer. The greatest danger is deep destruction. To prevent deep pitting, it is necessary to ensure a sufficient amount of the maximum allowable stresses in the depth of the layer, exceeding the effective equivalent stresses. The value of the allowable stresses is determined by the value of the contact endurance limit, depending on the mechanical properties of the material. The article discusses the results of experimental studies of the contact fatigue resistance of transmission gears of energy-saturated mobile machines made of cemented steel grades. It is established that the limit of contact endurance is related to the hardness of the material, determined by the Rockwell method, by a linear dependence. This dependence is taken as a basis for a comparative analysis of the calculated lifetime and experimentally established in the process of bench tests of gears. Taking into account the nonlinear nature of the ratio of hardness values determined by the Rockwell and Vickers scales, the relationship is obtained between the limit of deep contact endurance and the value of hardness measured by the Vickers scale with a load of 1.961 N. It is shown that the results of comparison of calculated and experimental data are greatly influenced by the limiting state of the deep contact pitting of the teeth of the tested gears. Statistical processing of calculated and experimental data was carried out. It is found that with the identity of the limiting state of the active surfaces of the gear teeth, the results of the lifetime calculation correspond to experimental data with a correlation coefficient of 0.964 and an average standard deviation of 13 %. The obtained expression for calculating the limit of deep contact endurance contributes to increasing the reliability of calculating the lifetime of gears provided by the resistance of deep contact fatigue.
Keywords gears, bench tests, contact deep pitting, contact fatigue resistance, lifetime calculation, deep contact endurance limit
  You can access full text version of the article.
Bibliography
  1. Tesker E.I. Sovremennye metody rascheta i povysheniya nesushchey sposobnosti poverkhnostno uprochnennykh zubchatykh peredach transmissiy i privodov [Modern methods of calculating and increasing the load-bearing capacity of surface-hardened gears of transmissions and drives]. Moscow, Mashinostroenie Publ., 2011. 434 p. (in Russ.).
  2. Fudzita K., Yokhida A. Vliyanie glubiny tsementovannogo sloya i otnositelnogo radiusa krivizny na dolgovechnost pri kontaktnoy ustalosti tsementovannogo rolika iz khromomolibdenovoy stali [Influence of cemented layer depth and relative radius of curvature on contact fatigue durability of cemented roller made of chromium-molybdenum steel]. Trudy amerikanskogo obshchestva inzhenerov-mekhanikov, 1981, vol. 103, no. 2, pp. 115–124 (in Russ.).
  3. Balashov B.A., et al. Reduktory energeticheskikh mashin [Reducers of power machines]. Leningrad, Mashinostroenie. Leningradskoe otdelenie Publ., 1985. 232 p. (in Russ.).
  4. Winter H., Weiss T. Some factors influencing the pitting, micro-pitting (frosted areas) and slow speed wear of surface hardened gears. Journal of mechanical design, 1981, vol. 103, iss. 2, pp. 499–505. DOI: https://doi.org/10.1115/1.3254945.
  5. Rudenko S.P., Valko A.L. Postroenie krivykh glubinnoy kontaktnoy ustalosti poverkhnostno uprochnennykh zubchatykh koles [Construction of deep contact fatigue curves for surface-hardened gear wheels]. Mechanics of machines, mechanisms and materials, 2022, no. 2(59), pp. 48–54 (in Russ.).
  6. Rudenko S.P. Raschet resursa zubchatykh koles transmissiy energonasyshchennykh mashin s uchetom kachestva khimiko-termicheskogo uprochneniya [Calculation of the lifetime of gear wheels of transmissions of energy-saturated machines, taking into account the quality of chemical heat hardening]. Mechanics of machines, mechanisms and materials, 2010, no. 4(13), pp. 58–60 (in Russ.).
  7. Alekseev V.I., et al. Aviatsionnye zubchatye peredachi i reduktory [Aviation gear transmissions and gearboxes]. Moscow, Mashinostroenie Publ., 1981. 374 p. (in Russ.).
  8. Kalner V.D., Shor F.I. Perevodnye tablitsy tverdosti [Hardness conversion tables]. Metallovedenie i termicheskaya obrabotka metallov, 1977, no. 9, pp. 59–61 (in Russ.).
  9. Valko A.L., Rudenko S.P., Sandomirski S.G. Perevod chisel tverdosti pri ispytaniyakh poverkhnostno-uprochnennykh stalnykh izdeliy [Translation of hardness numbers in testing of surface-hardened steel products]. Foundry production and metallurgy, 2022, no. 3, pp. 73–78 (in Russ.).
  10. Rudenko S.P., Valko A.L., Sandomirski S.G. Opredelenie effektivnoy tolshchiny uprochnennogo sloya tsementovannykh zubchatykh koles [Determination of the effective thickness of hardened layer of carburized gears]. Mechanics of machines, mechanisms and materials, 2022, no. 3(60), pp. 61–67 (in Russ.).