Title of the article Evaluation of the useing the needle-milling process for surface preparation in thermal spraying technologies
Authors

Belotserkovskij M.A., Doctor of Technical Science, Head of the Laboratory of Gas-thermal Methods of Machine Parts Hardening, the Joint Institute of Mechanical Engineering of the National Academy of Sciences of Belarus, Minsk, Republic of Belarus, This email address is being protected from spambots. You need JavaScript enabled to view it.">This email address is being protected from spambots. You need JavaScript enabled to view it.

Sheleg V.K., Doctor of Technical Science, Professor, Head of the Department "Mechanical Engineering", Belarusian National Technical University, Minsk, Republic of Belarus

Konovalova E.F., Assistant of the Department "Mechanical Engineering", Belarusian National Technical University, Minsk, Republic of Belarus

In the section TECHNOLOGICAL MECHANICS
Year 2014 Issue 4 Pages 69-73
Type of article RAR Index UDK 621.793 Index BBK  
Abstract The results of researches of metal surfaces roughness and adhesion of thermal spray coatings after needle-milling of the metal substrate are presented. The optimal parameters of the process to ensure maximum roughness are defined. It is shown that the strength of adhesion of metallic coatings after needle-milling does not satisfy the requirements of most parts of friction. The needle-milling process may be recommended for surface preparation prior to application of corrosion-resistant polymeric coatings only.
Keywords the needle-milling, the roughness, the gas-thermal spraying, the coatings, the adhesion
  You can access full text version of the article
Bibliography
  • Barshaj I.L., Sheleg V.K., Fel'dshtejn E.Je. Formirovanie kachestva poverhnosti i jekspluatacionnyh harakteristik detalej pri iglofrezerovanii i kombinirovannoj obrabotke iglofrezirovaniem i poverhnostnym plasticheskim deformirovaniem [Formation of surface quality and performance quality of parts during needle cutting and combined treatment by needle cutting and surface plastic deformation]. Minsk, BNTU, 2009. 231 p. 
  • Aktivirovannoe gazoplamennoe napylenie pokrytij poroshkami polimerov [Activated flame spraying of coating with powder polymers]. Uprochnjajushhie tehnologii i pokrytija [Reinforcement technology and coatings], 2007, no. 6, pp. 19-23. 
  • Cherepko A.E., Belotserkovskij M.A., Pryadko A.S.Tehnologii giperzvukovoj metallizacii [Technology of hypersonic metallization]. Mehanika-2011: sb. nauch. dokl. V Belorus. kongressa po teoretich. i prikladnoj mehanike [Mechanics-2011: Proc. V Belar. Kongr. on theoretical and applied mechanics]. Minsk, 2011, vol. 2, pp. 138-143. 
  • Khameneh Sh., Heydarzadeh M. Effect of grit-blasting parameters on the surface roughness and adhesion strength of sprayed coating. Surface and Interface Analysis, 2010, vol. 42, no. 6-7, pp. 551-554. 
  • Jashhericyn P.I., Maharinskij E.I. Planirovanie jeksperimenta v mashinostroenii [Experimental design in mechanical engineering]. Minsk, Vyssh. shk. Publ., 1985. 286 p. 
  • Zanadvorov V.S. Spravochnik po vychislitel'nym metodam statistiki [Handbook of computational approach of statistics]. Moscow, Finansy i statistika, 1982. 344 p. 
  • Belotserkovskij M.A. Tehnologii aktivirovannogo gazoplamennogo napylenija antifrikcionnyh pokrytij [Technologies of activated flame spraying of anti-friction coatings]. Minsk, Tehnoprint Publ., 2004. 200 p. 
  • Golopjatin A.V. Vlijanie morfologii poverhnosti jelementov tribosistemy na adgeziju napylennyh polimernyh kompozicij [The influence of the surface morphology of the tribosystem elements on adhesion of deposited polymer compositions]. Mehanika mashin. Teorija i praktika: materialy mezhdunar. nauch.-tehn. konf. [Mechanics of Machines. Theory and Practice: Proc. of the international. scientific and technical conf.]. Minsk, NIRUP «Belavtotraktorostroenie», 2003, pp. 382-389.