2_2020_sen_5

Title of the article

TECHNOLOGICAL INDICATORS OF THE OPERATION OF CUTTING BLANKS FROM SHEET MATERIAL WITH A WIRE TOOL WITH A MODIFIED SURFACE BY ELECTROEROSION METHOD
Authors

KISELEV Mikhail G., D. Sc. in Eng., Prof., Head of the Department “Engineering and Manufacture of Devices”, Belarusian National Technical University, Minsk, Republic of Belarus, This email address is being protected from spambots. You need JavaScript enabled to view it.">This email address is being protected from spambots. You need JavaScript enabled to view it.

MOSKALENKO Andrei V., Chief Engineer, Planar JSC, Minsk, Republic of Belarus, This email address is being protected from spambots. You need JavaScript enabled to view it.">This email address is being protected from spambots. You need JavaScript enabled to view it.

BOGDAN Pavel S., Ph. D. in Eng., Assistant, Belarusian National Technical University, Minsk, Republic of Belarus, This email address is being protected from spambots. You need JavaScript enabled to view it.">This email address is being protected from spambots. You need JavaScript enabled to view it.

MONICH Sergey G., Ph. D. in Eng., Senior Lecturer, Belarusian National Technical University, Minsk, Republic of Belarus, This email address is being protected from spambots. You need JavaScript enabled to view it.">This email address is being protected from spambots. You need JavaScript enabled to view it.

ANSCHITC Alexandr A., Student, Belarusian National Technical University, Minsk, Republic of Belarus
In the section TECHNOLOGICAL MECHANICS
Year 2020 Issue 2 Pages 46–54
Type of article RAR Index UDK 621.792.4 Index BBK  
Abstract The article is devoted to the experimental evaluation of the effect of EDM modifying the original smooth surface of the wire tool on its technological parameters when cutting different sheet materials, in particular, on cutting ability, surface quality of cut and quality of cut complex contours with sharp change of direction. It is shown that as a result of modifying the surface of the wire, single holes are formed on it that do not overlap each other, having metal flows on the edges that go beyond its original contour, which give it cutting ability. It was found that with an increase in the modification process, the energy of the electric discharge and the number of holes formed on the surface of the wire, its cutting capacity increases. It was established that when using the test wire tool, a clearly defined waviness is formed on the cutting surface, the appearance of which is due to the low rigidity of the tool, as well as the implementation of the process of destruction of the material both during its working and at idle. It is shown that the use of a wire tool with a modified surface makes it possible to ensure high quality and accuracy of cutting out of sheet materials with complex contour, characterized by a sharp change in the direction of its elements.
Keywords

wire tool, electroerosive surface modification, sheet material cutting, cutting capacity, cutting surface quality, complex contour
  You can access full text version of the article.
Bibliography
  1. Kiselev M.G., Mrochek Zh.A., Drozdov A.V. Elektrofizicheskie i elektrokhimicheskie sposoby obrabotki materialov [Electrophysical and electrochemical methods of material processing]. Minsk, Novoe znanie Publ., Moscow, INFRA-M Publ., 2014. 389 p.
  2. Eliseev Yu.S., Saushkin B.P. Elektroerozionnaya obrabotka izdeliy aviatsionno-kosmicheskoy tekhniki [Electrical discharge machining of aerospace engineering machinery]. Moscow, Moskovskiy gosudarstvennyy tekhnicheskiy universitet im. N.E. Baumana Publ., 2010. 437 p.
  3. Foteev N.K. Tekhnologiya elektroerozionnoy obrabotki [EDM technology]. Moscow, Mashinostroenie Publ., 1980. 184 p.
  4. Kozyr D.V. Issledovanie parametrov edinichnykh lunok, poluchennykh v rezultate elektroerozionnoy obrabotki s ispolzovaniem plazmennogo elektroda-instrumenta [Investigation of crater parameters by electrical discharge machining with plasma electrode-tool]. Izvestiya Tulskogo gosudarstvennogo universiteta. Tekhnicheskie nauki [News of Tula State University. Technical sciences], 2013, iss. 9, vol. 2, no. 4, pp. 350–357.
  5. Kiselev M.G., Monich S.G., Laputina D.G. Formirovanie poverkhnosti s chastichno regulyarnym mikrorelefom metodom elektroerozionnoy obrabotki [Surface forming with partly regular microrelief with electrical discharge machining]. Mekhanika mashin, mekhanizmov i materialov [Mechanics of machines, mechanisms and materials], 2017, no. 1(38), pp. 64–70.
  6. Kiselev M.G., Drozdov A.V., Moskalenko A.V., Bogdan P.S. Teoreticheskoe obosnovanie ratsionalnykh parametrov rezhima elektrokontaktnoy obrabotki provolochnogo instrumenta [Theoretical validation of rational parameters of the mode of wire tool electroerosion machining]. Vestnik Gomelskogo gosudarstvennogo tekhnicheskogo universiteta im. P.O. Sukhogo [Bulletin of Sukhoi State Technical University of Gomel], 2012, no. 3, pp. 3–10.
  7. Grigoryants A.G., Shigapov I.N., Misyurov A.I. Tekhnologicheskie protsessy lazernoy obrabotki [Technological processes of laser processing]. Moscow, Moskovskiy gosudarstvennyy tekhnicheskiy universitet im. N.E. Baumana Publ., 2006. 664 p.
  8. Kiselev M.G., Drozdov A.V., Moskalenko A.V., Bogdan P.S. Vliyanie rezhimov elektrokontaktnoy obrabotki poverkhnosti provolochnogo instrumenta na ee rezhushchuyu sposobnost, iznosostoykost i prochnost na razryv [The effect of conditions of electrocontact treatment of the surface of a wire tool on its cutting ability, wear resistance and tensile strength]. Vestnik Belorussko-Rossiyskogo universiteta [Bulletin of the Belarusian-Russian University], 2013, vol. 39, no. 2, pp. 55–62.
  9. Losev V.F., Morozova E.Yu., Tsipilev V.P. Fizicheskie osnovy lazernoy obrabotki materialov [Physical bases of laser processing of materials]. Tomsk, Tomskiy politekhnicheskiy universitet Publ., 2011. 199 p.
  10. Artamonov B.A., et al. Elektrofizicheskie i elektrokhimicheskie metody obrabotki materialov. T. 1. Obrabotka materialov s primeneniem instrumenta [Electrophysical and electrochemical methods of processing materials. Vol. 1. Processing materials with the use of the tool]. Moscow, Vysshaya shkola Publ., 1983. 247 p.
  11. Granovskiy G.I., Granovskiy V.G. Rezanie metallov [Cutting of metals]. Moscow, Vysshaya shkola Publ., 1985. 304 p.
  12. Matalin A.A. Tekhnologiya mashinostroeniya [Mechanical engineering technology]. Leningrad, Mashinostroenie Publ., 1985. 496 p.