2_2021_sen_5

Title of the article TASKS OF TECHNOLOGICAL SUPPORT OF THE AUTOMATED RING ROLLING COMPLEX
Authors

ANTONYUK Vladimir E., D. Sc. in Eng., Chief Researcher of the Laboratory of Metallurgy in Mechanical Engineering, Joint Institute of Mechanical Engineering of the NAS of Belarus, Minsk, Republic of Belarus, This email address is being protected from spambots. You need JavaScript enabled to view it.">This email address is being protected from spambots. You need JavaScript enabled to view it.

SANDOMIRSKI Sergei G., D. Sc. in Eng., Assoc. Prof., Head of the Laboratory of Metallurgy in Mechanical Engineering, Joint Institute of Mechanical Engineering of the NAS of Belarus, Minsk, Republic of Belarus, This email address is being protected from spambots. You need JavaScript enabled to view it.">This email address is being protected from spambots. You need JavaScript enabled to view it.

RUDII Victor V., Ph. D. in Eng., Chief Technologist, OJSC “BELAZ” — Management Company of Holding “BELAZ-HOLDING”, Zhodino, Republic of Belarus, This email address is being protected from spambots. You need JavaScript enabled to view it.">This email address is being protected from spambots. You need JavaScript enabled to view it.
In the section MECHANICAL ENGINEERING MATERIALS AND TECHNOLOGIES
Year 2021
Issue 2
Pages 42–53
Type of article RAR
Index UDK 621.81
DOI https://doi.org/10.46864/1995-0470-2021-2-55-42-53
Abstract The physical foundations and advantages of ring rolling are described. The materials science and technological processes of manufacture of products with its use are generalized. An analysis of the equipment of an automated ring rolling line was carried out, which showed that it is a complex and expensive technical solution. Moreover, the organization of the line with maximum load and efficiency is not included in the supplier’s tasks. The requirements for the maximum load of the line and its efficient operation have been determined. It is shown that the use of the experience of creating automated production of railway wheels when creating an automated production of ring blanks is impossible due to the need to ensure the production of rings of different structural shapes from different steel grades with different temperature ranges of plastic deformation and with different (from a hundred to several thousands) annual production programs. This requires the use of a different ratio of the radial and axial forces of the ring rolling, different technological equipment, taking into account different stiffness of the rings and their tendency to deformations during processing, transportation and cooling, a special development of mechanization means for readjustments. It is impossible to work out in advance all the technological options for the production of rings of different standard sizes on an automated line. In this regard, for the effective work of the complex, it is necessary to develop technological support and software for the manufacturing processes of each ring, to provide for the possibility of adjusting technological processes directly on the automated line with the participation of operators. On this basis, the tasks of technological support for the operation of the automated ring rolling complex at the OJSC “BELAZ” were formulated.
Keywords ring blank, heating, pressing, rolling, modeling, plastic deformation
  You can access full text version of the article.
Bibliography
  1. Marczinski H. Der Entwicklungsstand neuzeitlicher Ringwalzwerke. Stahl und Eisen, 1974, vol. 94, no. 24, pp. 1207–1211.
  2. Werner W., Volkmar S. Freiformschmieden und Ringwalzen verbessern Bauteileigenschaften. Sonderdruck aus MM Maschinenmarkt, 2000. 5 р.
  3. Kluge A., Faber H. Glühende Ringe – Das Ringwalzen als wichtiges Verfahren der Massivumformung. MM Industrie Magazin, 2005, pp. 26–31.
  4. Antonyuk V.E., Vityaz P.A., Parkhomchik P.A., Rudyy V.V., Shipko A.A. Koltseraskatka v proizvodstve detaley mashinostroeniya [Ring rolling in the manufacture of mechanical engineering parts]. Minsk, Belarusskaya navuka Publ., 2013. 188 p. (in Russ.).
  5. Vveden v ekspluatatsiyu koltseraskatnyy kompleks Muraro [The Muraro ring rolling complex was put into operation]. Gazeta Minskogo podshipnikovogo zavoda “Odinnadtsat”, 2017, no. 5(3229), pp. 1–3 (in Russ.).
  6. Storozhev M.V., Popov E.A. Teoriya obrabotki metallov davleniem [Theory of metal shaping]. Moscow, Mashinostroenie Publ., 1977. 424 р. (in Russ.).
  7. Tselikov A.I., Tomlenov A.D., Zyuzin V.I. Teoriya prokatki [Rolling theory]. Moscow, Metallurgiya Publ., 1982. 335 р. (in Russ.).
  8. Polukhin P.I., Gunn G.Ya., Galkin A.M. Soprotivlenie plasticheskoy deformatsii metallov i splavov [Resistance of metals and alloys to plastic deformation]. Moscow, Metallurgiya Publ., 1983. 352 р. (in Russ.).
  9. Kovka i shtampovka. T. 2. Goryachaya shtampovka [Forging and stamping. Vol. 2. Hot stamping]. Moscow, Mashinostroenie Publ., 1986. 692 р. (in Russ.).
  10. Groche P., Fritsche D. Inkrementelle Massivumformung. Werkstattstechnik, 2005, no. 10, pp. 798–802.
  11. Doege E., Behrens B.-A. Handbuch Umformtechnik. Springer Verlag, 2007. 913 р.
  12. Puller S. Simulation des Werkstoffflusses beim Ringwalzen mittels elementarer Plastitatsteorie. D. Sc. Thesis. Hannover, 2003. 110 p. Available at: https://www.repo.uni-hannover.de/ handle/123456789/6293 (accessed 03 March 2021).
  13. Meier H., Pentleit A. Mechanisches Deformationsmodell für das Ringwalzen. Zur Berechnung der maximal zulässigen Zentrierarmkräfte beim Radial-Axial-Ringwalzen. Werkstattstechnik wt-online, 2003, vol. 93, no. 5, pp. 485–488.
  14. Marchenko М. Radial-Axial-Ringwalzen. Dynamische 3D-Visualisierung eines Radial-Axial-Ringwalzprozesses. VDM Verlag Dr. Müller, 2010. 84 p.
  15. Koltseprokatnye stany. Otlichnoe kachestvo dlya trebovatelnykh zakazchikov [Ring rolling mills. Excellent quality for demanding customers]. SMS Meer, 2004. 24 p. (in Russ.).
  16. Antonyuk V.E., Sandomirski S.G. Dinamicheskaya stabilizatsiya malozhestkikh kolets posle kol’tseraskatki [Dynamic stabilization of rings of low rigidity after the ring rolling]. Mechanics of machines, mechanisms and materials, 2020, no. 3(52), pp. 34–41 (in Russ.).